Eureka Tents Tent alpenlite 2XT User Manual

D
• Stake the tent down. Pull  
the floor taut as you work.  
Always stake through the  
web loops or rings, not  
through the grommets.  
See fig.8.  
• Insert the locking post on the front right  
pole into a grommet on the web at the  
front of the tent at A. Place the other front  
pole into the grommet at B. See fig.3.  
C
fig.8  
ASSEMBLY INSTRUCTIONS  
APENLITE 2 XT  
• Locate the short pair of tent poles. Stand  
at the rear of the tent and insert the  
tapered end of one of these poles into  
the diagonal hole in the junction tube  
E
• Drape the fly over the tent  
with the vestibule over the  
front door.  
Component List:  
1 Tent Body,  
1 Spanner,  
1 Tent Fly,  
2 Front Poles,  
2 Rear Poles ,  
F
1 Center Hoop, 2 Junction Tubes, 1 Carry Bag,  
1 Stake Bag w/ Stakes  
marked “Rear Right.” Insert the second  
short pole into the other diagonal hole in  
the junction tube.  
1 Pole Bag,  
fig.3  
• Fold the fly back and reach  
under it to attach the Velcro®  
fasteners, from the inside of  
fly, to the frame and junction  
tubes. See fig.9.  
fig.9  
NOTE: Do not drop tent bag or pole bag on its end. Do not bounce  
tent bag on its end to get the tent out. These actions may cut the  
shock cord and/or damage the pole ends.  
• Insert the locking post on the rear  
right pole into a grommet on the web  
at the rear of the tent at C. Insert the  
other pole into the grommet at D.  
See fig.3.  
Assembly:  
• Unroll and unfold the tent with the floor on the ground. Remove the  
fly and set it aside. Do not stake the tent down yet. In windy  
conditions, we recommend that an end should face into the wind  
and that you stake down one corner of this end. See fig.1.  
• Connect the four corner  
buckles from the fly to their  
mates on the tent corners.  
A
B
fig.4  
• Stake out the rear vestibule  
loop. Move to the front of  
the tent, pull out the front  
vestibule and stake down the stake out loops. Draw these out  
until the webs on the vestibule are tight. Work you way around  
the tent and stake out the side webs. Take care, the fly must  
not contact the tent body. Tighten all straps as needed.  
See fig.10.  
• Locate the spanner and insert one end through  
the center hole of the front junction tube.  
• Join the shockcorded poles together and separate according to size.  
Try to prevent pole sections from snapping together, as this can  
damage the pole ends. Make certain that each insert has seated  
firmly into each plain end.  
IMPORTANT: Disconnect rods in the middle of  
the spanner. See fig.4. Insert the opposite end of  
spanner through the rear junction tube. Push  
down on the disconnected rods until they spring  
back together. This forms a free standing frame.  
• Connect tent to frame. Pull the shockcord loops at  
the peak of the tent up and over the junction tubes.  
Attach the tent clips to the poles. See figs.5 and 6.  
fig. 2  
fig.5  
fig.6  
F
fig.10  
Your tent is ready for use.  
fig. 1  
• The tent features a High/Low venting, side opening door that  
will increase the amount of air flow through the tent.  
• Insert a locking end tip of the  
curved center hoop into the  
E
front  
grommet on the side web at  
Attach the three pole clips to the  
center hoop.  
E.  
• In strong winds, tie extra lines to the storm loops on the fly and  
stake down. Adjust the sliders so that the lines are tight.  
fig.7  
• Locate the longer pair of tent poles. Stand at the front of the tent and  
insert the tapered end of one of these poles into the diagonal hole in  
the junction tube marked “Front Right.” Insert the second long pole  
into the other diagonal hole in the same junction tube. See fig.2.  
• Attach the junction tubes to the tents. Tie the included cord to  
the shockcord. Then, feed the other end through 1/8” hole in  
the tube and tie a knot. This will help prevent loss and make the  
tubes easier to find in the dark.  
• Move to the other side of the tent. Bend the center hoop down over  
the spanner and insert the end into the side web grommet at  
Attach the three remaining clips to the center hoop. See fig.7.  
F
.
REV. C 4-09  
 

Abocom Switch HF1000 User Manual
Addonics Technologies Computer Drive HDUS11325DX User Manual
Agilent Technologies Portable Generator 83622B User Manual
Aiwa Car Stereo System CDC MP3 YU User Manual
American Sensor Carbon Monoxide Alarm CO8B User Manual
Asus Network Card TRL DLS User Manual
Athena Technologies Speaker 3PAB005E User Manual
BB Electronics Surge Protector 232HSP User Manual
Beko Electric Grill D531 User Manual
Beko Freezer GN162320X User Manual